How to replace a whirlpool refrigerator water filter. Every six months, the Whirlpool refrigerator water filter needs to be updated.
If you replace it more often, the water from the refrigerator will not taste bad, but it may be murky and have black dots. The water filter replacement may interfere with the refrigerator’s operation, resulting in slower water flow and smaller ice blocks.
Installing a new water filter is a simple procedure that requires no particular skills or equipment. When buying new filters, get the ones that match the model number of your favorite brand.
Attempting to install the incorrect filter will render this impossible, as these filters differ in design and quality!
How To Replace A Whirlpool Refrigerator Water Filter
We will discuss here steps on how we can replace a whirlpool refrigerator water filter.
Step 1: Locate Your Water Filter
When it comes to finding the exact location of where your water filter rests, you should take a look at your model’s manuals.
Some models will have the water filter mounted behind the front grille at the base of your refrigerator. Still, other models might also have them inside your refrigerator towards the upper right-hand corner.
Keep an eye out for the model number when deciding on a Whirlpool refrigerator. You can find this information either on a sticker located inside the fridge or somewhere in the owner’s manual.
Step 2: GET PREPARED
There will be some spillage when you change your water filter, so put down a towel before removing the filter. You may also want to remove any food or drinks that might be in the way of replacing the filter.
If changing the water filter on your refrigerator requires you to open up the ice maker compartment, be sure to turn off the ice maker while working on it because spillage could occur if ice is made while you’ve removed the water line.
Older refrigerators may require that power be cut when drawing the water line, but this step should not be necessary with most modern models.
You shouldn’t have to access any electrical components to change a refrigerator’s water filter; thus, it should be safe to replace without cutting power from your appliance!
Step 3: Remove The Old Filter
If your filter is located in the fridge grille, you can remove it by pushing it down on the button left and then simply pulling it out.
If your filter doesn’t have control over it, you can remove it by turning it counterclockwise, which should Release it and cause it to come out.
Sometimes you need to Push in as you Turn to get the filter out. If your Whirlpool refrigerator has a filter inside the fridge, you will first need to remove the cover (or Push in some models).
Once that’s taken off, push the button on either side of the filter (depending on your model) or Push up at all four corners until the whole thing rotates upwards, after which you’ll be able to pull out such a filter from its casing.
Sometimes filters can be quite difficult to remove, so if they are stuck fast, press them harder into their casing, which should help release them!
Step 4: Install The New Filter
Most Whirlpool refrigerators with water filters feature a color-keyed cap. The cap to your filter should be unscrewed from the old filter and screwed onto the new filter before changing it out.
You should also make sure you have transferred the cap to the freshwater filter before installation so that you don’t interfere with locking it into place when it comes time to connect it.
Installing a new water filter can sometimes be a challenge. Replace the old cartridge with the new one, sliding it into the water filter slot of your refrigerator.
It can sometimes be difficult due to them being different sizes or if they must be turned upright at a certain angle – but replacing these filters may save hundreds of dollars in repairs that might occur in your appliance’s pump or similar components.
Make sure you insert this correctly against little arrows indicating flow direction if present!
FAQs
Where is the water filter for the Whirlpool refrigerator?
Whirlpool refrigerator water filters can be found in one of two places. The access panel is on the interior’s upper-right wall if your refrigerator has a twist-in filter. The push-in models are hidden behind a metal grille on the lower left side.
After changing the filter, how long should you run the water?
Make sure you use only cold water to run through your faucet before filling a pot with water and placing the filter inside to soak for five minutes after this time has elapsed.
Run some more cold water before attaching the filter under the faucet where it will be easily accessible whenever you want it.
Conclusion
We hope you have enjoyed this article about how often to replace your refrigerator water filter. We want you to know that it is important to always clean and replace your refrigerator water filter regularly to ensure that your drinking water tastes good and is safe.
Related Guides
